MANUAL AUTORIZACION BTP PDF

Edinson Borda Villcas. Test de Percepcion Visual Frostig Manual. Uploaded by. MARIA Abs Cambios Uploaded by. Patricio Patri. Manual Autorizacion Btp. Manual Autorizacion Btp. Uploaded by. Patricio Patri · PROBMON1-Ser Omni 6- 25 Min (Problemas). Uploaded by. Patricio Patri · Test Psi Co Tec Nico. Manual Autorizacion Btp Descripción: PROGRAMACIONES BTP INFORMÁTICA HONDURAS M Topographie 2-Approfondissement BTP- TSGT.

Author: Doutaxe Dougami
Country: Costa Rica
Language: English (Spanish)
Genre: Video
Published (Last): 23 September 2006
Pages: 263
PDF File Size: 4.55 Mb
ePub File Size: 3.97 Mb
ISBN: 802-7-12471-748-8
Downloads: 68501
Price: Free* [*Free Regsitration Required]
Uploader: Daizshura

Disc should be angularly adjusted within the clearance of the bolt holes, to get the correct centre height of the tool. These components may have to be replaced during periodic inspection about once in a year.

Remove rear cover Check for free movement of sliding coupling rollers in drum cam groove. Fitment of tool disc on the turret. Denel Turret Lct30 Full description. Electric motor Encoder Proximity switch 61 Final assembly Spindle assembly Final assembly 1 1 1 Use extraction screws and pull out the end plate Requirements of turret control: Turret Demolition Scope 1Full description. In case of a 12 station turret bolts 15 may not be in line with the holes.

Assembly Reference Quantity Drg.

Pragati – BTP Turret Manual

Replacement or adjustment of rotary encoder Rotary encoder is fitted on flange 19 with the help of clamps In the event of a collision, dowel pins can get sheared or damaged. It might therefore be necessary to employ high pressure coolant pump, to ensure sufficient flow at tool point. This design ensures that the coolant is connected only to the working tool position.

  IEC 61116 PDF

Btp italia salvo62barbato Education.

Indexing cam 75 may be in a single piece, or in two pieces depending on method of manufacture. Procedure for setting the encoder in proper angular orientation is as follows: If turret cannot be indexed even by hand cranking, it will be necessary to open up the turret for inspection.

List of Spare Parts No.

Btl all components as shown in figure Switch is held in a manuwland the clamp is bolted to the turret body by socket head screw Orientation marks on gears 73 and 83 should be positioned as shown in figure Turret should be aligned by dialing surface of the indexing flange.

If the clearance is more, it should be adjusted by replacing the flange 25 by a new flange of suitable extra thickness. Turret is lubricated by medium viscosity gear box oil.

Pragati – BTP Turret Manual – PDF Free Download

If the turret does not function properly immediately after an accident, internal component damage can be suspected. Proximity switch adjustment and replacement fig.

Do not disconnect wiring. Put the lubricating oil Page Operation of the switch can be checked by hand-cranking the turret. Bolts should be tightened in gradual manner, in 3 to 4 stages.

Rent E Books Manual Autorización Btp Epub | Website for downloading cbse books!

Remove end cover of motor. Adjustment of Ringfeder Clamps In rare cases, it is possible that accident can occur while the turret is indexing spurious signals in control circuit can unintentionally start the indexing cycle, causing the turret to index in the middle of a machining operation. It is convenient if the assembly could be clamped to the table with the help of a plate as shown in the drawing. One revolution of cam shaft completes one indexing inde xing cycle of declamp-index-clamp.

  COCHAYUYO PECTINA PDF

To link to this article: Remaining components of the cam shaft are to be assembled at a later stage. This is a difficult operation to be done on site, and is most likely to be less than perfect.

Manuual also give excellent protection against damage by hot chips. However, dowel pin can be used for the purpose of alignment, but it is recommended to remove the autorizacikn after clamping the tool disc in position. Now the encoder can be fitted back in position. Suggested electrical circuit is on page 9.

Remove coolant flange 26 and coolant ring 24,1. Laporan btp pdf Documents. Crank turret by hand, and check the function of switch by watching the signals on the built in LED. Tighten opposite bolts in sequence 1,5,2,6,3,7,4,8.