The DS, DSA, and DS digital thermometers provide 9, 10, 11, .. Throughout this data sheet, the term “conversion” is used to refer to the entire. The DS digital thermometer and thermostat provides 9-, , , or bit . as explained in the CONFIGURATION REGISTER section of this data sheet. DS CMOS Dual Peripheral Driver (discontinued). The DS series of dual peripheral drivers was designed be a universal set of interface components .

Author: Zulkisar Arashakar
Country: Ethiopia
Language: English (Spanish)
Genre: Software
Published (Last): 28 November 2004
Pages: 344
PDF File Size: 9.70 Mb
ePub File Size: 5.3 Mb
ISBN: 468-4-44381-170-8
Downloads: 89550
Price: Free* [*Free Regsitration Required]
Uploader: Dogrel

Again, just an easy demo to get connected to the DS User Control Panel Log out. Mysil Super Member Total Posts: JM, thanks for your help with this The manufacturer recommends this device for such applications as monitoring the temperature within electronics enclosures for networking equipment, cellular base stations, and portable products, but it should function just ds131 well for reading ambient air temperature or even the temperature change resulting from a user picking up and holding a device.

I would suggest trying Debug breakpoints automatically disabled Future of PIC32 16F88 cannot set internal oscillator frequency beyond I may have to see if there are any of those still around to play with. The DS measures environmental temperature and provides temperature readings serially to a circuit.

There seems to be no counter and slop registers in the DS, but it does have variable resolution — up to 12 bits — which lets you get hi-res temperatures back. After struggling through understanding the wire. The DS is I2C. It hangs forever while waiting for status change. A quick glance at data sheets hint, hint suggests that thought DS and DS are similar devices, they’re miles apart as far as interface goes.


Datasehet, the Start Conversion command value is different. The Datasheeet sensor looks like a good choice for many temperature-measurement situations.

Looks like the is the ‘s new big brother. Tried it anyway but it didn’t fix anything. You change the resolution via bits in the configuration registers. I’ve tried for days now and still can’t make this thing to work! Not that that does me much good since I’m just not that good at the electronic stuff — more a programmer, dafasheet.

DS Datasheet(PDF) – Maxim Integrated Products

The DS and DSA sensor families exhibit similiar characteristics and operations but with a few differences – see the relevant datasheet for these devices for more about their operation. Nikel Starting Member Total Posts: There are a number of user-configurable options – all such settings are stored in non-volatile EEPROM that will retain values for at least 10 years without being powered.

Using the DS in DS applications: DS or B4 AG thanks again for your help, isaac. This sensor uses a two-wire serial interface that is funcitonally equivalent to I2C for reading and writing data.

Hi Dario, thanks for the reply. Looks like you are trying to use the I 2 C library to talk to it? In thermostat mode, the sensor is pre-programmed by the user with upper and lower temperature limits and will change the state of output pin Tout when one of these limits is reached.


DS Datasheet(PDF) – National Semiconductor (TI)

What are good practices when using SPI? Can’t help about this Code. The serial dafasheet used also allows up to eight of these devices to share a single two-wire serial bus and allows the designer the freedom to place temperature sensing components at a distance from the host circuit if desired.

This means that once options are set the sensor will retain all settings even if power is not applied. Essentials Only Full Version.

Maybe it’s just too many differences, but any help would be greatly appreciated! I also tried with code examples that I found on the internet that acted directly on the ports themselfs without setting up I2C module that isbut could not get that to work either, so I opted for MCC code since I believed it to be the most reliable solution.

DS1631, DS1631A, DS1731 High-Precision Digital Thermometer And Thermostat

Any help will be much appreciated! The temperature conversion time is a measure of how long the sensor takes to respond to a request from the host circuit and includes the time required to acquire a temperature reading and convert the temperature reading into a binary word.

Debugging on the other hand doesn’t seem to adtasheet working, I get a “Could not acquire hardware tool communications resources: My connections are standard, like this: