BC558 TRANSISTOR DATASHEET PDF

DataSheet: PDF icon BCPDF. BC is a general purpose PNP transistor. It is used in switching and amplifier applications. The DC current gain varies in. BC Transistor Datasheet pdf, BC Equivalent. Parameters and Characteristics. Semiconductor data sheets and/or specifications can and do vary in different applications . BC / BC / BC VCE = -5 V, IC = µA.

Author: Vilkree Doura
Country: Czech Republic
Language: English (Spanish)
Genre: Music
Published (Last): 18 February 2013
Pages: 277
PDF File Size: 6.99 Mb
ePub File Size: 16.43 Mb
ISBN: 384-4-73616-975-1
Downloads: 10973
Price: Free* [*Free Regsitration Required]
Uploader: Mezikora

Interface SD Card with Arduino. The BC because of this large gain value is normally used to as a audio amplifier. BC has a gain value of to ; this value determines xatasheet amplification capacity of the transistor. The voltage divider is the commonly used biasing mode.

Transisotr input signal at base is amplified and taken at the emitter. Datxsheet resistor is always added in series with base pin to limit the base current. Virgin Galactic — Commercial Space Flight. It is also used as a complement for transistors BC to BC In the below GIF you can notice the transistor being switched for a low voltage 1v audio signal.

For switching applications, transistor is biased so that it remains fully on if there is a signal at its base. A Transistors acts as an Amplifier when operating in Active Region. Of the above types common emitter type which amplifies voltage is the popular and mostly used configuration. BC as switch Tranwistor a transistor is used as a switch it is operated in the Saturation and Cut-Off Region as explained above.

  HORST KROHNE PDF

When this transistor is fully biased then it can allow continues current of transistod to flow across the collector and emitter. SPI Module of Arduino. The DC current gain varies in range to When base current is removed the transistor becomes fully off, this stage is called as the Cut-off Region and the Base Emitter voltage could be around mV.

BC Pinout, Configuration, Circuit As Switch & Amplifier

It can amplify power, voltage and current at different configurations. The value of this resistor RB can be calculated using below formulae. Complete Technical Details can be found in the BC datasheet given at the end of this page.

The transistor terminals require a fixed DC voltage to operate in the desired region of its characteristic curves. This is known as the biasing.

Arduino based GPS receiver. Choosing Battery for Robots. Amplifier modules like Audio amplifiers, signal Amplifier etc.

For amplification applications, the transistor is biased such that it is partly dataaheet for all input conditions. As discussed a transistor will act as an Open switch during Forward Bias and as a closed switch during Reverse Bias, this biasing can be achieved by supplying the required amount of current to the base pin.

  AIRLINE FINANCE BY PETER S.MORRELL PDF

Transistor BC558

Submitted by admin on 26 March BC is a general purpose PNP transistor. What is Web Browser. When uses as an Amplifier the DC current gain of the Transistor can be calculated by using the below formulae.

Choosing Motor For Robots.

This high-density System-in-Package SiP integrates controller, power switches, and support components. Also note that a PNP transistor is always used for high side switching, meaning the collector datawheet connected to power and emitter to load that is to be switched.

BC is used in common emitter configuration for amplifiers.

BC is a PNP transistor hence the collector and transistot will be closed Forward biased when the base pin is held at ground and will be opened Reverse biased when a signal is provided to base pin. It is used in switching and amplifier applications.

Interface GPS with Arduino.

TL — Programmable Reference Voltage. Where an input signal of low voltage is amplified switched to high voltages t0 drive loads like speakers. Skip to main content. When a transistor is used as a switch it is operated in the Saturation and Cut-Off Region transostor explained above. In the absence of base signal, it gets completely off.