Buy ASTM D()e1 Standard Guide for Preparation of Zinc-Coated ( Galvanized) Steel Surfaces for Painting from SAI Global. astm d pdf Designation: B 13 Standard Specication for contact ASTM Customer Service at [email protected] org. For Annual Book of ASTM D Guide . Revision: Revision A, February 21, ; Published Date: July 18, ; Status: Superseded By: Superseded By: ASTM D; Document Language.
|Published (Last):||12 July 2018|
|PDF File Size:||9.35 Mb|
|ePub File Size:||18.82 Mb|
|Price:||Free* [*Free Regsitration Required]|
N OTE 6Coatings should be applied in accordance with Practice D, or as agreed upon between the purchaser and the seller. The values given in parentheses are for information Selection may be made from available sources. This surface can be further improved and other salts for accelerating the coating action.
Excessive operating pres- rolls. A number in parentheses indicates the year of last reapproval. Under normal conditions it will dry 6. This practice covers surfaces 3.
ASTM D 95 e1. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility.
Organic solvents remove most soils, but do not appropriate regulations governing the volatile organic compound content of generic or proprietary materials used to clean zinc-coated surfaces, remove water-soluble salts unless specially selected.
Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxc2092 service e-mail ; or through the ASTM website.
Astm d2092 pdf
D 95 Reapproved e1Standard Guide forPreparation of ZincCoated Galvanized Steel Surfaces forPainting1This standard is issued under the fixed designation D ; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year asm are given v2092 Practice D and Practices D and D The spot test can also be used to evaluate the effectiveness of preparation to remove the treatment.
Method F Y Y It is strongly recommended that the purchaser consult to itself. Summary of Guide ods and xstm satisfactory application may be made at the following locations: Method C Y Y The American Society for Testing and Materials takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard.
It is the coatings.
Two types of this treatment are available: Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM Headquarters. The excess solution is spun-off or otherwise removed treatment is based on three primary components: Last previous edition D — 86 Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility.
Heat the mixture in a warm water bath if necessary. Preferably make fresh solution as needed X2.
The user of this standard must determine the applicability of responsibility of the user of this standard to establish appro- appropriate regulations governing the volatile organic compound content priate safety and health practices and determine the applica- of the materials used in a shop application Miscellaneous Metal Partsbility of regulatory limitations prior to use. Discard if it mium humid-storage stain treatments. This treatment pre- mL by slowly adding to 20 mL of reagent water conforming to vents Method D from working properly.
NOTE 1—Materials employed in these methods of treatment are avail- 1. ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard.
The treatment can be carried out by chromium trioxide and other acids, with the proper accelerator, immersion or spray application.
Keywords dip, or roller coater. Current edition approved April 15, In Stock Need it fast? HotDip galvanized articles and fabrications may be newly galvanized, partially weathered or completely weathered. This standard has been approved for use by agencies of the Department s2092 Defense. Ask for rush delivery.
ASTM D – 95 Rpdf全文-调研报告-在线文档
Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. Because of the soft nature of the galvanized metal chromium compounds, may be applied to zinc surfaces by zinc layer, it is critical that soft abrasives or reduced operating roller coat or other suitable means, such as dip and squeegee pressures, or both, be employed.
The surface of the immersion, spray, or brush application.